Ferramentas para bombas diesel (2.)

Modular system for testing the camshaftless pumps manufactured by Zexel, with sizes:
- PFR1K.., PFR2K.., PFR3K.. PFR4K..
- PFR3KD, PFR4KD
- PFR3MD, PFR4MD
The cambox can be applied on any test bench for the diesel fuel injection pumps.
This configuration is supplied in one wooden box and includes the following components:

- Universal Cambox (9562-M1) and spacer (9562-M4 and 9562-M5)
- 4 cyl camshafts (9564-A and 9564-E)
- Fixing plate for Zexel PFR .. 1K (9562-T)
- Fixing plate for Zexel PFR .. 2K (9891)
- Fixing plate for Zexel PFR .. 3K (9892)
- Fixing plate for Zexel PFR .. 4K (9893-D)
- Fixing plate for Zexel PFR .. 3KD/MD (9562-MD3)
- Fixing plate for Zexel PFR .. 4KD/MD (9562-MD4)
- Rods (9562-F and 9562-L) and fuel control connector (9562-G, 9562-I, 9562-R and 9562-LB )
- Cambox mounting flange (9478-BXS)
- Drive coupling (9576)

O flange 8155-E garante a fixação centralizada da maioria das bombas cr (Bosch CP1, CP3, CP4, Delphi, Denso, VDO), em qualquer bancada de testes.
O flange é equipado com 4 anéis de redução para encaixar os diâmetros do cubo de 50, 60, 68, 80 mm, bem como as bombas CP1K.
O flange requer berço universal 9680-A ou similar.

Swivel vice for Common-rail pumps

Universal clamping bracket to hold several flanges allowing the centered clamping of flanged diesel injection pumps.
The 125 mm centering height and 20mm guide (Bosch standard) can be adapted to different requirements, by the proper adapting spacers.

Sistema modular para testar as bombas sem eixo de cames do tamanho PFR1K .., PFR2K .., PFR3K .. e PFR4K .. fabricadas pela Zexel.
O cambox pode ser aplicado em qualquer banco de ensaio para as bombas de injeção de combustível diesel.
Esta configuração é fornecida em uma caixa de madeira.

Wrench to fix/remove the flange, shaft and pulley on the following pumps ZEXEL VP. The timing pin is included.

Flange for fixing ZEXEL VP pumps on test benches. It requires the universal bracket 9680-A)

8225-CP3 helps to determine if the ZME valve can be retained, instead of installing a new one, on CP3 and CP1-H pumps.
Similar to 0 986 613 270

New version of the b racket 9562-S. This revised design is suitable for the PFM1P100 pumps and the 0 141 401 106 as well.

Pair of universal flat bracket to install both P and H pumps, simply by placing or removing the thickness of adaptation

Kit to determine if the ZME valve can be retained, instead of installing a new one, on CP4 pumps.

Splined coupling to drive CP3.4 (MAN) pumps on any test bench.
Similar to 1 685 702 092

Flexible pipe ( cr 2500BAR) to connect the high pressure delivery from the pump outlet to the rail. Nuts 14x15 / 14x1,5. Similar to 1 680 712 324

This device allows to monitor the pump body pressure (5 BAR).
It is also equipped with ball valve, to measure the negative pressure generated by the pump.
Caution: Not all test benches are able to supply the amount of flow required by the comon rail pumps. Therefore, it is crucial to monitor that, during the test, the pump does not go into cavitation.

Pair of mounting bracket for the easy disassemble and reassemble of HP0 pumps. The bracket has to be installed on the swivel vice 9260.

High pressure swivel fitting Male 14x1,5 - Female 12x1,5

High pressure swivel fitting Male 14x1,5 - Female 14x1,5