Skip to Content

ECOMMERCE


  1. Продукты
  2. Книга Марбеда

Книга Марбеда

Marbed's Book

  • Since 2011, the Marbed's Book has been organized into three color-coded sections: 
    1. green: test bench equipment, 
    2. red: tools for pumps, 
    3. blue: tools for injectors.

  • Subcategories enable you to progressively refine your search for specific products.

 

EUR (ecommerce)
Сортировать по: Рекомендуемые

Книга Марбеда

Bracket
Plate for BOSCH 1 cyl.pump with location clamp for determining the delivery start ratio, with rod guide
Универсальная базовая распределительная коробка для размещения насосов без распределительного вала до 4 цилиндров на испытательном стенде.Распределительная коробка должна быть правильно сконфигурирована (монтажная пластина, проставка, распределительный вал, заглушка рычага управления, скользящий шток) в зависимости от типа проверяемого насоса.
Cambox universal base to house camshaftless pumps up to 4 cylinders on the test bench.
The cambox must be configured correctly (mounting plate, thickness - if required -, camshaft, control lever connection, sliding rod), depending on the type of pump to be tested.
Chiave a bussola dentata_
Insert external diameter 6,3 mm.with inside hole diam.2,8 mm.on Stanadyne pumps.
Comparator holder to measure the travel on the governor magnet. Similar to 0 986 612 657
Inseritore paraolio albero comando pompa DPC
Oil seal inserter for pump drive shaft
Supporto comparatore brevettato
Puller
Sliding hammer with adapter to extract Bosch CRIN injectors on Iveco Eurocargo
Checking gauge
Checking gauge for the protrusion level of 25 and 35 mm camshaft cones
Similar to Bosch reference 0 986 611 278, KDEP 2924.
Single reamer for the shaft bushing of the VE pump (nominal diameter 20 mm). Similar to 0 986 611 958
Single reamer for the shaft bushing of the VE pump (nominal diameter 17 mm). Similar to 0 986 611 951
Pre-stroke measuring device, to adjust the delivery start and measure the tappet clearance on the TDC, in the PE (S) .. P, with M24 x 1.5 connection. Similar to BH 1688130085 - 1688130112 -1 688 040 071
MS checking set
Checking set for "MS" level determination on EP/VE with LDA
Кабель переходник 81.03.104
Кабель-переходник для насосов BH P..RE24, P..RE30, R..RE31 (Iveco, Scania, Volvo) (номер BH 0 986610104 - KDEP-P400 / 3), снабженный данными испытаний
High pressure test pipes for test bench (unbent), covered by rubber
Specifications:
- external diameter: 6 mm
- internal diameter: 1,6 mm
- thickness: 2,2 mm
- length: 350 mm
- nuts: M12x1,5 mm - M14x1,5 mm
Similar to Bosch reference 1 680 750 085
25 mm conical coupling
25 mm conical coupling to drive diesel pumps on any test bench. Length 100, teeth 12 mm
The puller 9463 is recommended to unplug the shaft.
Conical coupling
25 mm conical coupling to drive diesel pumps on any test bench. Length 58, teeth 12 mm
The coupling is equipped with internal nut for locking and pulling out the shaft.
Similar to Bh 1 686 430 026 - Bh1 686 430 030
Conical coupling
20 mm conical coupling to drive diesel pumps on any test bench, lenght 58, teeth mm 12.
The coupling is equipped with internal nut for locking and pulling out the shaft (BH 1 686 430 024)
Motoring coupling without back plate
Cushioned motoring couple 4008/1 ISO normative for Bosch test beds without back plate
Needle valve
Needle valve for ISO test injector type IV (0 681 443 014)
Синхронизация насосов VE: поворотный кронштейн с круговой шкалой для косвенного измерения хода поршня. Похож на Denso 95095-10400.
Универсальная опора компаратора увеличенная 8x1 для насосов EPVA ... VE, Nippondenso