Skip to Content

ECOMMERCE


  1. Ürünler
  2. Hand Tools

Hand Tools

Marbed's Book

  • Since 2011, the Marbed's Book has been organized into three color-coded sections: 
    1. green: test bench equipment, 
    2. red: tools for pumps, 
    3. blue: tools for injectors.

  • Subcategories enable you to progressively refine your search for specific products.

 

EUR (ecommerce)
Sıralama: Öne Çıkan

Hand Tools

Bracket
Plate for BOSCH 1 cyl.pump with location clamp for determining the delivery start ratio, with rod guide
Universal basic cambox
Cambox universal base to house camshaftless pumps up to 4 cylinders on the test bench.
The cambox must be configured correctly (mounting plate, thickness - if required -, camshaft, control lever connection, sliding rod), depending on the type of pump to be tested.
Chiave a bussola dentata_
Insert external diameter 6,3 mm.with inside hole diam.2,8 mm.on Stanadyne pumps.
Bit for the governor control cover screw on DP2100 pumps. Similar to 7244-438.
Comparator holder to measure the travel on the governor magnet. Similar to 0 986 612 657
Inseritore paraolio albero comando pompa DPC
Oil seal inserter for pump drive shaft
Supporto comparatore brevettato
Dial gauge holder.
Comparator bearing to survey the rod stroke for A-B-BV pumps
Puller
Sliding hammer with adapter to extract Bosch CRIN injectors on Iveco Eurocargo
Checking gauge
Checking gauge for the protrusion level of 25 and 35 mm camshaft cones
Similar to Bosch reference 0 986 611 278, KDEP 2924.
Single reamer for the shaft bushing of the VE pump (nominal diameter 20 mm). Similar to 0 986 611 958
Single reamer for the shaft bushing of the VE pump (nominal diameter 17 mm). Similar to 0 986 611 951
Pre-stroke measuring device, to adjust the delivery start and measure the tappet clearance on the TDC, in the PE (S) .. P, with M24 x 1.5 connection. Similar to BH 1688130085 - 1688130112 -1 688 040 071
Universal comparator support with rocker arm and return spring
Universal bracket with rocker arm and return spring, for holding the comparator during the measuring of the rack travel on inline pumps.
MS checking set
Checking set for "MS" level determination on EP/VE with LDA
Adapter cable 81.03.104
Adapter cable for BH pumps P..RE24, P..RE30, R..RE31 (Iveco, Scania, Volvo) (BH ref. 0 986 610 104 - KDEP-P400/3), fitted with test data
High pressure test pipes for test bench (unbent), covered by rubber
Specifications:
- external diameter: 6 mm
- internal diameter: 1,6 mm
- thickness: 2,2 mm
- length: 350 mm
- nuts: M12x1,5 mm - M14x1,5 mm
Similar to Bosch reference 1 680 750 085
25 mm conical coupling
25 mm conical coupling to drive diesel pumps on any test bench. Length 100, teeth 12 mm
The puller 9463 is recommended to unplug the shaft.
Conical coupling
25 mm conical coupling to drive diesel pumps on any test bench. Length 58, teeth 12 mm
The coupling is equipped with internal nut for locking and pulling out the shaft.
Similar to Bh 1 686 430 026 - Bh1 686 430 030
Conical coupling
20 mm conical coupling to drive diesel pumps on any test bench, lenght 58, teeth mm 12.
The coupling is equipped with internal nut for locking and pulling out the shaft (BH 1 686 430 024)